Tag Archives: smoking problems

A Wind Cap vs A Chimney Cap

Wind cap
A Wind Cap

Enjoying a warm fire on a cold evening is one of the simple pleasures in life, but not when that beautiful crackling fire is accompanied by the eye-burning smell of smoke.

There are a number of causes for fireplace smoking problems, many of which are easily remedied.

If you live in areas prone to wind, such as the coastal or mountain region, or even off of a canyon or hillside, there is a very simple solution–a chimney wind cap.

 

The difference between a Wind Cap and a standard Chimney Cap

Chimney cap
A Standard Chimney Cap

A standard chimney cap serves several important purposes:
* Prevents embers from landing on the roof;
* Prevents animals and other critters from entering the home through the chimney;
* Prevents rain from going into the chimney system; and
* Prevents debris, leaves and pine needles from entering the chimney.

A standard cap, however, will not prevent wind-induced downdrafts.

What is a Wind Cap?

Wind caps have the same benefits as standard chimney caps but due to the design, wind caps have the added benefit of preventing wind from going down the flue which can cause smoking problems in your home.

Wind caps work on the same premise as weather vanes.  They rotate on a turret, turning their back to the wind while allowing the smoke to exit the flue pipe. The wind currents flow over the cap, instead of going down the pipe. The air current going past the wind cap creates a venturi effect (partial vacuum) in the pipe, helping to prevent the downdraft that creates the smoking problem. The hood of the wind cap also prevents horizontal rain from entering the flue pipe.

Where to find a Wind Cap

Unlike universal standard chimney caps, wind caps must be custom sized to fit the flue pipe. This requires taking accurate measurements of the inside and outside diameter of the flue pipe as well as the shape of the chimney flue pipe. The measurements can be tricky, especially for the odd-sized or odd-shaped flue pipe. Wind caps have to be special ordered to fit properly. It is recommended to hire a professional chimney sweep to measure, order and install a wind cap. To find a CSIA Certified Chimney Sweep, go to the Chimney Safety Institute of America’s website.

One precaution with a wind cap

Please be aware that a wind cap cannot be installed on a pre-fabricated fireplace system due to the U.L. listing on the pre-fab fireplace. A wind cap can be installed on a masonry chimney and the pipe of some freestanding wood stoves and stove inserts.


Fireplace smoking problems may be easily resolved. Don’t just accept a fireplace smoking problem. Nothing should take you away from enjoying one of the simple pleasures in life.

What is a Masonry Chimney?

A masonry chimney on the exterior wall of a home

Just like automobiles that have different manufacturers and models, the same goes for fireplaces and chimneys.

Here in Southern California, there are primarily three different types of open fireplace systems–1) masonry chimneys; 2) prefabricated, factory-built systems; and 3) Rampart General Pre-Cast systems. Since I’ve already addressed Rampart General Pre-Cast systems in the past, this post will be about the masonry chimney.

The History of the Masonry Chimney

These masonry systems have been around for many centuries and are tried and true. They are constructed on-site with bricks, stone, concrete blocks and mortar. Masonry systems are built by hand, brick by brick. If the system is built properly and maintained regularly and there are no extenuating events (such as earthquakes and wildfires), they will last a century or more. In fact, it’s not uncommon to see masonry chimneys still in use in houses built in the 18th and 19th centuries.

Unfortunately, due to the high cost of labor, these systems haven’t been constructed since the mid-1980s here in Southern California except for in high-end, custom-built homes.

For a fireplace to work properly, there is a formula involved in building a masonry chimney system. Some of the factors in this formula have to do with the height of the chimney, the diameter of the flue pipe, and the height/width of the firebox opening. If a system isn’t built properly, the chimney will never draw properly and will have ongoing smoking problems.

Components of a Masonry Chimney and Fireplace

It’s important to know the various components of a masonry chimney:

Flue cap – The chimney cap consists of spark arrestor material with a solid lid. It provides three primary benefits: 1) It prevents embers from getting on the roof; 2) It prevents birds, rodents and other critters from entering the home through the chimney; and 3) Flue caps with solid lids will also prevent most of the rain from coming down the flue lining. Without the solid flat lid of the cap, rain would land in the smoke shelf which may cause damage to the damper and may deteriorate the firebox.

Crown – The crown is a concrete or mortar surface at the very top of the chimney structure. Its purpose is to direct water Masonry chimney componentsaway from the structure. A crown can also be referred to as a “wash” or a “splay.” A cracked crown will allow moisture to get into the chimney structure, eventually creating cracks in the chimney structure.

Flue – The flue is the passageway from the firebox to the top of the chimney structure. In a masonry chimney, the flue is lined with a flue lining typically made from terra cotta, pumice or metal.

If the flue lining is cracked, broken or if the mortar joints are missing between the flue tiles, the system cannot be used because of heat transference or deadly carbon monoxide leaking into the house. There are three primary methods for repairing cracked flue linings–1) relining the system with a stainless steel pipe; 2) installing a stove insert with a metal pipe to the top of the chimney structure; or 3) a poured cement, cast-in-place system.

In addition, older systems may not have a flue lining at all (which is referred to as an “Unlined Chimney”). In this case, the system cannot be used until it has been repaired.

Flue tiles – A flue lining inside a flue is basically a vent pipe. This pipe is not one solid pipe. In most cases, the pipe (typically terra cotta or pumice) is made up of pipe sections called flue tiles. Each flue tile (pipe section) is anywhere from 12″ to 24″ tall. In between each flue tile is the mortar. There should not be any gaps or voids in the mortar joints.

Smoke Shelf – A horizontal shelf located behind the damper to prevent down drafts and to collect debris that has fallen down the chimney.

Damper – The device that opens and closes so that heat is not lost from the home when the fireplace is not in use. Some dampers can be installed at the top of the chimney flue.

Lintel – A horizontal metal piece that extends over the entire width of the firebox opening at the top of the firebox opening. It is a structural part of the firebox. Here’s important information on why you never want to remove a lintel.

Firebox – The area of the fireplace where the fire is burned.

Exterior Hearth Extension – The area that extends in front of and to the sides of the firebox opening. The exterior hearth extension should be made from non-combustible materials and should be differentiated from the rest of the room’s flooring.

Ash Dump – Not all masonry systems have an ash dump. This is the area below the firebox where the ashes can be swept down into. A firebox with an ash dump will typically have a metal plate in the firebox’s floor. This metal plate can be opened to brush the ashes below.

Clean-out Door: The clean-out door is located on the outside of the chimney structure near ground level to clean out the ashes from the ash dump.

Unlined Masonry Chimney

Before the early 1900s, masonry systems were not constructed with a flue lining. We refer to those systems as “Unlined Chimneys.” According to the Chimney Safety Institute of America, “Never use a chimney that does not have a liner or has a damaged or improper lining.” [Public Safety Bulletin issued by the Chimney Institute of America: The Importance of Flue Lining in Your Masonry Chimney.] Here in San Diego, however, we have seen unlined chimneys as late as the early 1960s.

When these unlined systems were originally built, the masons used a material called parging (like stucco). They hand-coated over the bricks and mortar joints inside the chimney flue. With time, age and usage, this parging material has worn away, leaving the bricks and mortar joints exposed. In addition, back then the masons used a lot of sand in their mortar. Eventually, these mortar joints disintegrate, leaving gaps and voids. This creates a potentially dangerous situation.

If the unlined chimney is structurally sound and there are no other issues with the system, the system can be “relined.” This is a method where a stainless steel pipe is installed inside the chimney structure. However, if the metal lining is not installed properly or is undersized, the fireplace can be dangerous and/or will not ever draw properly.  Relining a chimney should only be done by a licensed and qualified chimney professional.

Make sure to use a CSIA Certified Chimney Sweep to inspect your system and sweep it if needed. If your masonry chimney is maintained, it will give you warmth and comfort for many years, decades and maybe even centuries to come.


Caveat: Chimneys are built differently in various regions throughout the country. What is common in one region may not be common in another. This information provided here is based on what we see in Southern California.

Chimney windcap

Wind Caps Solve Fireplace Smoking Problems

Feet in front of fireplaceEnjoying a warm fire on a cold evening is one of the simple pleasures in life, but not when that beautiful crackling fire is accompanied by the eye-burning scent of smoke.

There are a number of causes for fireplace smoking problems, many of which are easily remedied. If you live in an area prone to wind, such as the coastal or mountainous regions, or even off of a canyon or hillside, there is a very simple solution–a chimney wind cap.

The difference between a standard chimney cap and a wind cap

Standard chimney capA standard chimney cap prevents embers from landing on the roof, prevents animals and other critters from entering the home through the chimney and prevents rain from going into the chimney system. These standard chimney caps, however, will not necessarily prevent wind-induced down drafts.

The wind cap, on the other hand, has the same benefits as a standard chimney cap but due to its design, it has the added benefit of preventing wind from going down the flue, causing smoking problems in your home.

What is a wind cap?

WindcapA wind cap works on the same premise as a weather vane.

The specially-designed wind cap rotates on a turret, turning its back to the wind while allowing the smoke to exit the flue.

The wind currents flow over the wind cap, instead of going down the pipe. The air current going past the cap creates a venturi effect (partial vacuum) in the pipe, helping to prevent the down draft that creates the smoking problem. The hood of the  wind cap also prevents horizontal rain to enter the flue pipe.

Where to find wind caps

Unlike universal standard chimney caps, wind caps must be custom sized to fit to the flue pipe. This requires taking measurements of the inside diameter of the flue pipe, the outside diameter of the flue pipe as well as the shape of the chimney flue. The measurements can be tricky, especially for the odd-sized or the odd-shaped flue pipe.

These wind caps have to be special ordered to fit properly. It is recommended to hire a professional chimney sweep to measure, order and install a wind cap. To find a CSIA Certified Chimney Sweep, go to the Chimney Safety Institute of America’s website.

One precaution with a wind cap

Please be aware that wind caps cannot be installed on pre-fabricated fireplace systems due to the U.L. listing on the pre-fab fireplace. Wind caps can only be installed on masonry chimneys or wood stove pipes.


Smoking problems can be easily resolved. Don’t just accept a fireplace smoking problem. Nothing should take you away from enjoying your warm cozy fireplace on a cold night–one of the simple pleasures in life.

50 Tips For Enjoying Your Fireplace

There’s nothing better than a warm fireplace on a cold evening. If you haven’t got one yet you are most definitely missing out!  Here are 50 quick and simple tips that will help you safely enjoy that cozy fire even more.

IMPORTANT SAFETY TIPS

1. For an open fireplace, the glass doors must be in a fully open position. Once the fire has died out, close the glass doors before you go to bed at night.

2. Always make sure that the fire screen in front of the fireplace is closed when the fireplace is in use. Even when the fireplace is not in use, keep the fire screen closed to discourage pets from going into the firebox. (Cats have been known to use the fireplace as a litter box.)

3. Never leave a fire in the fireplace unattended, especially when children and pets are present.

Carbon monoxide detector4. Install smoke and carbon monoxide detectors in your home, especially close to the fireplace as well as near bedrooms and in the kitchen. Make sure to test them at least twice a year.

5. According to the Chimney Safety Institute of America, homes should have a minimum of two 5 lb ABC fire extinguishers. There should be one fire extinguisher per floor of a house and the fire extinguishers should be visible and accessible. A fire extinguisher should be close at hand when the fireplace is in use.

6. Never use kerosene, lighter fluid or gasoline to start your fire.

7. Keep combustible materials (like knickknacks, newspapers, firewood and Christmas trees) away from the firebox opening. This includes items hung from the mantel, like Christmas stockings and garland.

8. Inspect your landscaping near the chimney. Trees and vines should be kept a minimum of 10 feet away from the top of the chimney.

FIREWOOD AND ARTIFICIAL FIRE LOGS (SUCH AS DURAFLAME)

9. Be sure your firewood is aged and kept dry from the rain or snow.

Pile of firewood10. Hardwoods should be aged a minimum of one year while softwoods should be aged a minimum of six months. The moisture in firewood should be between 15%-20%. Aged and dried wood will provide you with more efficient fires, fewer smoking problems, and less flammable creosote build-up in the chimney.

11. Do not burn construction scraps or wood that have been chemically treated, such as plywood, paneling or particleboard. In addition, don’t burn paper with colored ink, cardboard, Christmas wrapping paper, plastics, fabrics made from synthetic materials, or junk mail. The chemicals can be toxic when burned.

12. To easily start a fire, use fat wood or fire starters if you don’t have a log lighter.

13. Buy your wood in the spring or summer to allow it to dry out before the burning season.

14. A cord of wood is 4 feet x 4 feet x 8 feet. A rick of wood is one third the volume of a cord of wood. A truck-load of wood would be dependent on the size of the truck bed and is not an easy way to determine how much wood you’re actually buying. A truck-load could mean anything from a short-bed pick-up truck holding 1/5 cord to a pulpwood truck that can hold four cords.

15. A cord of wood is a legal unit of measure. If you buy a cord of wood, have the wood cut to burning length, split and stacked and not just dumped in your driveway. Although you may pay more, you will know for certain that you weren’t cheated and that the wood will be aged in time for the burning season.

16. Stack wood on top of a pallet instead of directly on the ground to avoid pests and mold in your firewood.

Duraflame log and firestarter17. If you’re burning artificial fire logs (like Duraflame), do not place wood on top or below the artificial fire log.

18. Never poke or break open an artificial fire log while it’s burning.

19. Only burn one artificial fire log at a time.

20. Do not cook food over artificial fire logs because of the chemicals in this product.

21. Never burn artificial fire logs in free-standing stoves or stove inserts.

SMOKING PROBLEMS

22. During cold weather, always prime your flue before lighting your fire to prevent smoking problems, especially if you commonly have a smoking problem at the beginning of a fire.

23. Airtight homes are more prone to smoking problems. This is especially true in newer homes or homes that have been retrofitted with new windows. If this is the case, crack open a window close to the fireplace.

24. Avoid having the heater/furnace or air conditioning on at the same time as the fireplace especially if the air intake register for the furnace is close to or in the same room as the fireplace. During a fire, you may lose the draw on the fireplace because the furnace can pull smoke and gases down the chimney and back into the living area.

25. Always use a fire grate in the fireplace. This allows airflow under the fire to help in the combustion process and will give you a better fire.

26. Place your firewood on the fire grate close to the back wall to prevent smoking problems.

DAMPER

27. Always check to make sure your damper is fully open before you light the fire.

28. Do you always forget which way your damper is open? Put a note on the underside of your mantel that says which way the damper is open. If you don’t remember which way the damper opens, you’ll remember where to look to find out!

29. Close your damper when you’re not using your fireplace so you won’t lose heat during the winter and air conditioning during the summer. An open damper is like having an open window.

30. If your existing damper is broken or non-existent, and if you burn wood, consider installing a top sealing damper to prevent heat loss from the home.

31. If you have gas logs in an open fireplace, the damper must be locked in a fully open position.

CLEANING OUT THE FIREPLACE

32. You don’t have to clean out the fireplace after every use. In fact, a healthy bed of ashes below the grate can actually be beneficial. Once the ashes reach the bottom of the grate, the ashes should be spread out or removed since it’s important to have good airflow from under the grate.

33. Wait at least 72 hours after your last fire before cleaning out the ashes in your firebox.

34. When you’re cleaning out the ash and debris from the fireplace, spread slightly damp, used coffee grounds over the ashes before you clean it out. It’ll prevent the ash from becoming airborne and make it easier to clean out.

35. Wear a mask while cleaning out the firebox to avoid breathing fly-away soot and ash.

36. Don’t use your home vacuum cleaner to vacuum the ashes from your fireplace. You stand the chance of ruining your vacuum cleaner. Also, household vacuum cleaners and shop vacs don’t have good enough filters so you run the risk of “dusting” your living room.  Instead, use a small whisk broom and dustpan to remove the ashes from the fireplace.

37. Place ashes in a metal can with a lid. Make sure the can is not placed on a wood deck or patio afterward.

38. If you have artificial gas logs, it’s common to have a light sooting on the logs where the flames lick up over the logs. This is not a safety issue and is totally natural. Simply use a soft bristle brush (like a paintbrush) to dust off the soot. Never wash or scrub the artificial gas logs or you will remove the paint from the logs.

39. Don’t throw away used ashes. They have many beneficial uses, such as: providing necessary nutrients to gardens, composting, insect deterrents (snails and slugs), de-skunking a pet, shining your silver, controlling pond algae, melting ice, and even making soap.

CHIMNEY CAPS

black chimney cap40. A chimney cap serves three main purposes: 1) will prevent embers from landing on your roof, your neighbor’s roof, your solar panels, your car and your landscaping ; 2) will prevent birds and other critters from entering your home through the chimney; and 3) can prevent water intrusion into your chimney which will deteriorate your chimney prematurely and will also extend the life of your damper.

41. If your home is located off of a canyon or hillside, your chimney may be more prone to smoking problems. A specially-designed windcap can minimize smoking problems in this case.

OTHER IMPORTANT INFORMATION TO KNOW

42. Pre-fab fireplaces, typically in condos and homes built after the 1980s, are intended more for ambiance and romance than for heat. In this type of fireplace, you should not have a fire any larger than what you would get if you are burning one artificial fire log, like Duraflame. Having large or overly hot fires in pre-fab fireplaces may cause damage to the fragile refractory panels inside the firebox and those panels are expensive to replace.

43. Consider a heat shield or fireback to protect the backwall of your fireplace. It will extend the life of the firebox.

44. Odor problems, or as I like to say “stinky chimneys,” can be caused by smoking problems, animals in the chimney, a dirty chimney, the type of fuel you’re burning (especially wood that is wet or not aged), the pressurization in your home, or rainwater in your chimney.

45. Reconsider mounting a TV above your fireplace. Heat and dust particulates aren’t good for electronics and doing this may void the TV manufacturer’s warranty.

46. If you’re buying a new home, have your chimney inspected by a CSIA Certified Chimney Sweep during the inspection period. If you have just bought a home, have the chimney inspected before using it for the first time. You never know what or how much the previous owner burned.

47. If you have a masonry chimney and you live in a region with a lot of rain or snow, consider weather sealing the masonry to prevent spalling and deterioration of the bricks and to avoid expensive masonry repairs later on.

48. Only use a CSIA Certified Chimney Sweep to inspect or sweep your chimney. To find a CSIA Certified Chimney Sweep, go to the website for the Chimney Safety Institute of America.

49. According to the National Fire Protection Association, chimneys should be inspected on an annual basis and swept if necessary.

50. To save money, do this important maintenance in the spring and summer when the rates are the lowest and when the schedule is less impacted.


Fireplaces are the best part of winter. Following these simple hints will give you the most enjoyment from a cozy fire.

8 Reasons NOT to mount your TV above the fireplace

TV above the fireplace
Photo credit R. Pocock

Installing a TV above the fireplace is a very common decorating style in homes these days, but does that make it right? Here are some valid reasons to reconsider the location of your TV.

1) Electronics are sensitive to heat. The heat and smoke will reduce the lifespan of your TV. When you use your fireplace, heat rises. This is how your TV above the fireplace will come into direct exposure to the heat from the fire. This is especially true in cases where you have a heat exchange system or a stove insert inside the firebox which generate far more heat than a regular open wood-burning fireplace. In addition, the wall behind the TV may have some radiant heat from the heat going up the flue pipe inside the chimney, so your TV could be exposed to heat from the front as well as from the back. Televisions already generate a lot of heat on their own without additional exposure to the heat from the fireplace. Some manufacturers of televisions and other electronics recommend a maximum heat as low as 90°F.

2) Besides heat, dust particles create problems in electronics. Soot particles or particulates in the smoke from your open wood-burning fireplace can damage your TV. When you’re having a smoking problem from your fireplace, particulates will enter the TV above the fireplace. If your fireplace has a smoking problem, here are some solutions to solve that problem and reduce the amount of particulates into the home.

3) Due to the two reasons listed above, some television installation professionals state that installing a TV above the fireplace may void out the warranty on your TV. Make sure to contact the manufacturer and the retailer to verify that your warranty will be valid if you insist on installing your TV this way.

4) Television manufacturers recommend that televisions should be at eye level. The resolution of the TV is designed to be viewed from a specific angle. If you’re viewing the TV from too far right or left, or if the TV is located too far above the ideal viewing position, the TV screen may appear washed out and may lose some brightness. Adjustable mounts may alleviate some of those issues but not all.

5) Neck strain is a prominent problem with televisions mounted above the fireplace mantle. Imagine watching a movie in the theater from the front row. Sore neck and back muscles, stiff necks, and headaches can be caused by sitting in an unnatural position for any period of time.

6) Any kid or teenager will be the first ones to say that playing their X-boxes and Play Stations aren’t as easy to play when the TV is located above the fireplace.

7) During the mounting process, if the TV isn’t installed properly, you can ruin the fireplace and chimney system. Over the past few years, I’ve received a number of phone calls from panicked homeowners who drilled through the wall above the mantle straight into the chimney pipe. If you miss the stud, the drill can go clear through the drywall and into the metal chimney pipe on a prefab fireplace system. Homeowners and professional television installers don’t know just how close the chimney pipe for the prefab fireplace may be to the wall. If a hole has been drilled into the metal pipe, the flue pipe is compromised and the system can no longer contain the elements of combustion. In that case, the pipe must be replaced and, in some cases, the entire prefab fireplace system as well. In addition, it’s never a good idea to install the cables and electric cords behind the wall inside the chimney chase.

8) Most interior decorators will agree that a TV above the fireplace is not aesthetically pleasing because it takes away from the true focal point of the room–your beautiful fireplace. Also, we know as chimney sweeps, how much homeowners love to decorate their mantles which is harder to do with a TV blocking a majority of the mantle.


 

Televisions are expensive, and none of us want to see them damaged and quit before their time.   My advice is to consider other locations to put your television instead of above that fireplace!

An Easy Solution for a Fireplace Smoking Problem

If the furnace is on at the same time as a fireplace, you may experience a smoking problem, especially if the air intake grill is close to the fireplace.

Common Scenario: On a cold, winter night, you decide to have a warm, cozy fire in your open fireplace to take the chill out of the living room. Your house is still cold and your furnace turns on automatically. A short time later, you notice the air in the room is getting smoky. All of a sudden, that nice cozy fire isn’t so nice and you know you’re going to be smelling smoke for days.

A fireplace smoking problem is a common occurrence. Ethical chimney sweeps will always suggest the simplest and most cost-effective solution to a smoking problem. One of the most common and very easy-to-fix causes is “dueling furnaces and fireplaces,” competing for the same finite amount of air in a house. This is especially true in a relatively new home or a home with new windows where the home is “tight” and energy efficient.

Tight houses don’t make for good fires in open fireplaces.

Competition for Air

Tight weatherstripping on doors, double-pane windows, sealed vapor barriers and upgraded insulation in walls and attics make for a well-sealed house, creating a house with a finite amount of oxygen.

Cold air register grill for furnace. If the furnace is on at the same time as a fireplace, you may have a fireplace smoking problem.
Photo credit: Rick Pocock

A fire in an open fireplace requires a great deal of oxygen. It draws a huge amount of air from the living area and draws it up the chimney. This is a natural draft system. Whereas, the air intake grill for a furnace pulls massive amounts of air from the home into the furnace. This is a mechanical draft system.

If an open fireplace (with a natural draft) is close to the air intake grill for a furnace (which uses a much stronger mechanical draft), the furnace will always win because the draw for the furnace is stronger than the draw for the fireplace. Mechanical is stronger than natural.

This means that you’ll lose the draft (upwards motion of the air in the fireplace flue), resulting in drawing the smoke into the room.

The closer the open fireplace is to the furnace air intake grill as well as the tighter the house, the more likely you can experience a smoking problem when the furnace and fireplace are on at the same time.

This is especially important to know when you have artificial gas logs in your fireplace because those gases going up the flue are colorless and odorless. If the furnace is on at the same time, you won’t know if those gases from the fireplace are being pulled into the room instead of going up the chimney flue.

Other systems in your home can also have this same reversing effect on the fireplace, such as: Whole house fans, kitchen stove hoods, bathroom fans, clothes dryers and central vacuums. These systems draw air from the house and exhaust to the outside.

Slightly opening a window close to the fireplace may help in this case.  This will provide the necessary make-up air that a fire needs to provide for a good draw.

For other potential causes of smoking problems, check out our blog post on the Top 10 smoking problems and their respective solutions. To find an ethical and reputable C.S.I.A Certified Chimney Sweep, go to the Chimney Institute of America website.

Rule of Thumb

Avoid having the forced air heater or furnace turned on at the same time as an open fireplace and get back to enjoying that cozy fire!

Six Causes of Fireplace Odors

Fireplace odor like a campfireThere’s nothing better than a warm, cozy fire in the fireplace but there’s nothing worse than the “campfire-in-the-living-room” smell that can sometimes occur afterwards. Understanding some of the causes for a stinky fireplace will help prevent the problem. There are several key causes for fireplace odor issues.

 

1) Smoking Problems

Sometimes a smoking problem is so subtle that you may not even realize it at the time of the fire but then you notice a bad odor the next day. That’s because smoke rises to the highest part of the house at the time of the fire but by the next day, that smoky odor drifts down into your breathing range. This smell can be absorbed into carpeting, furniture and window coverings so it’s important to avoid the smoking problem in the first place. To prevent smoking problems, check out our blog post on the Top 10 Smoking Problems and their Respective Solutions.

In addition, if you’re using your fireplace at night, the damper has to stay open all night. Hours later, halfway through the night when the fire is down to just burning embers, the chimney loses its draw, especially if the furnace turns on, pulling air down the chimney, resulting in the smoke and resulting odors coming into the room. To prevent this night-time issue, make sure your fireplace has tight-fitting glass doors.

2) Animals

Animals love your chimney because it is a dark place, safe from predators, but once animals enter chimneys, it’s extremely difficult for them to fly or crawl back out on their own. This might mean your chimney will smell of aChimney capnimal feces or worse, a dead animal. In fact, due to federal animal protection laws, there are heavy fines of up to $15,000 for removing live migratory birds without special animal-removal permits. To remove an unwelcome animal from your chimney, contact an animal removal organization with the proper permit, but the better way would be to avoid birds and other critters from using your fireplace as their new home in the first place by installing a chimney cap.

3) Dirty Chimney

A dirty chimney can cause a bad fireplace odor because of the smoking problem but also even when the fireplace is not in use. Downdrafts push air down the chimney, bringing with it the smelly particulates from the dirty chimney and sending a campfire smell into the room. Having a CSIA Certified Chimney Sweep to sweep the chimney will help, but keep in mind that creosote can absorb into the porous material of a flue lining so even if a chimney lining is meticulously swept, there may still be a fireplace odor. Keeping the damper closed and installing tight-fitting glass doors will help.

4) Type of Fuel

Burning wood that has not been aged long enough or has been left out in the rain will create a smokier fire which can cause a rank odor. Some people can also be very sensitive to the petroleum odor of certain brands of prefabricated logs. In this case, change your fuel type and make sure that wood is aged and kept dry.

5) Pressurization in the home

To make our homes more energy efficient, builders are making houses “tighter.” Tight homes don’t make for properly-operating fireplaces. Fire needs oxygen, a great deal of oxygen, and it pulls it from the room. If a fire can’t get that oxygen because your fireplace is competing with other systems in the home such as furnaces, clothes dryers, bathroom exhaust fans or kitchen hoods, pressurization problems will occur in the home and can create a smoking problem or fireplace odors. Even if the fireplace isn’t in use, these other systems will draw air down the chimney, pulling down the particulates from a dirty chimney or odors from the ashes in the fireplace. Wind-driven downdrafts will also create this effect. Even during the summer, when fireplaces aren’t being used, rainy weather or high humidity can bring fireplace odors into the house. We recommend closing the damper, keeping the firebox clean, installing tight-fitting glass doors on the front of the fireplace or creating another method to bring make-up air into the home.

6) Rain/Water intrusion

Fireplace odors occur during rainRain falling down a masonry chimney doesn’t land directly in the firebox. Instead, because of the way a masonry chimney is designed, this rain lands in an area behind the damper called a smoke shelf unless the chimney has a cap. The rain collects in the smoke shelf until the water eventually evaporates. This rain water mixes with soot and can have a rancid, musty odor. This is another good reason to have a chimney cap on the top of the chimney.


Fireplace odors are a common problem but with a little knowledge, odors can be avoided, decreased or completely eliminated. Reduce smoking problems, have your chimney swept regularly, install tight-fitting glass doors, provide make-up air in tight homes to prevent pressurization problems, and install a cap to keep out rain and animals. Then sit back and enjoy your fireplace without the smell of regret the next day. After all, the smell of a campfire can be enjoyable on a camping trip, but not in your living room!

Rolled up newspaper used in priming the flue

Priming the fireplace flue

Rolled-up newspaperWhat does a rolled-up newspaper have to do with preventing a smoking problem in a wood-burning, open fireplace?

One of the most common causes for smoking problems in open hearth fireplaces is due to homeowners not priming the fireplace flue before starting the fire, especially during cold weather.  An indication that this is the cause of a smoking problem is if you notice smoke in the room at the beginning of a fire, so it’s a good habit to prime your flue every time you use your fireplace.

Explanation

When it’s cold outside, it’s also cold inside the flue pipe and this cold air is very “heavy air,” especially if it’s cold and/or damp outside. If you light a fire, the smoke rises, but it can’t because the cold air acts like a plug. Instead of the smoke trying to rise up the pipe, the smoke can come into the room where you’re sitting. If you don’t prime the flue, eventually the air inside the pipe will warm up enough on its own but not before filling the room with smoke. Priming the flue is essentially pro-actively starting the draw.  Doing this is especially necessary in chimneys that are on an exterior wall of the house.

Steps to Priming the Flue

1) Open up the damperPriming the flue
2) Place the wood or fire log on the grate3) Tightly roll up a piece of newspaper like a wand or torch and hold it up near the open damper
4) Hold it there for a minute or two until you see the smoke being drawn up the flue
5) Start the wood or fire log on fire

This will heat up the air inside the flue and will get the draw started.

What NOT to do!

It’s potentially unsafe to use the log lighter (the gas pipe under the grate) to prime the flue.  Using the log lighter for this will eventually warm up the air in the flue, but in the meantime, the gases can enter the room where you’re sitting.

In summary….

There is nothing better than a cozy fire on a cold, winter night but that joy can be totally cancelled out by a house full of smoke. Smoking problems can be caused by many reasons but priming the flue is an easy solution for smoking issues. Getting into the habit of priming the flue will go a long way in enjoying that cozy fire in the fireplace.  Bottom line: Don’t throw away those newspapers anymore; they’re good for more than just reading!

Smoke coming from fireplace

Ten Fireplace Smoking Problems and Solutions

Smoke coming from fireplaceAs a professional chimney sweep, the most common phone call I get is about fireplace smoking problems.  Sometimes the smoke can fill the room; other times you may not even realize you have a smoking problem because the smoke is so subtle.  If it smells like a campfire in your living room the day after having had a fire in your fireplace, the likelihood is that you had a smoking problem that was so minor, you didn’t even realize it. Here are solutions to the top ten most common smoking problems.

Dirty Chimney

During usage of the fireplace, the smoke goes up the flue (the passageway or pipe). The smoke coats the flue with a by-product called creosote. With usage, the creosote buildup becomes thicker as the flue becomes smaller. This coating is not only dangerous because it’s highly flammable, but will create a smoking problem that will get progressively worse as the creosote builds up and the flue becomes narrower. The Chimney Institute of America (CSIA) states that if the build-up of creosote is any more than 1/8″ in the flue, the chimney must be swept.

SOLUTION: Have the chimney swept by a qualified CSIA Certified Chimney Sweep. To find a CSIA Certified Chimney Sweep, go to the Chimney Safety Institute of America at www.csia.org.

Obstructions inside the Chimney and/or Plugged-up Chimney Cap

Birds inside a chimneyThe chimney should be checked for any obstructions inside the flue pipe, such as bird nests, tree branches, leaves, beehives, or even the missing volleyball. (Yes, we really do find balls in chimneys!) Also, with usage, the chimney cap will get plugged up, especially if you burn wet wood or lots of paper.

SOLUTION: Have the chimney swept by a qualified CSIA Certified Chimney Sweep. To find a CSIA Certified Chimney Sweep, go to the Chimney Safety Institute of America at www.csia.org

Closed Damper

Before lighting a fire, always make sure that the damper is open. Don’t laugh–a closed damper happens more often than you think!  If you’re not sure if the damper is open or closed, shine a flashlight inside the fireplace, up the flue. If the damper isn’t fully open, do not even attempt to light the fire.

SOLUTION: Always check the damper each time before starting a fire. As chimneys get older, sometimes the damper will become difficult to operate or may even seize. If the damper does not FULLY open, have it looked at by a CSIA Certified Chimney Sweep.

Fuel–Firewood or Prefabricated Logs (like Duraflame)

Firewood that has not been aged long enough will have a higher moisture content which will not only create a smokier fire but will create more creosote buildup Pile of firewoodinside the flue pipe. According to the Chimney Safety Institute of America, ideally, the moisture content of firewood should be between 15% and 25%. A good rule of thumb is to have firewood aged between six months and a year. Firewood should be split to dry out faster. Dried wood that is wet from rain and snow will re-hydrate so be sure to cover up the firewood pile during wet weather. In addition, improper usage of the prefabricated logs (such as Duraflame or Pine Mountain) can create a smoking problem.

SOLUTION: Make sure that firewood is aged at least six months and keep the wood dry during the winter.

Cold Weather

When it’s cold outside, there’s also cold air inside the flue pipe and that cold air is very heavy, dense air, especially if it’s raining outside. That cold air acts like a plug. If Priming the flueyou light a fire, the smoke can’t rise but instead will come into the room where you’re sitting. That cold air in the flue will eventually warm up on its own during a fire, but not before smoke comes into the living area.

SOLUTION: During cold weather, always “prime the flue” before starting your fire. To do this, place the wood on the fire grate as far back as possible in the firebox. Open the damper. Roll up a piece of newspaper like a “wand.” Light the end of the wand and hold it up near the open damper for a minute or two to warm up the air in the flue. When the flue is primed, you should see the smoke from the wand being drawn up the flue. At that point in time, light the fire.

Central Heating System or Furnace

If you have the furnace turned on at the same time as having a fire in the fireplace, you may experience a smoking problem. This is especially true when the furnace’s Cold air register for furnaceair intake (cold air register) is close to or in the same room as the fireplace. Other systems like kitchen hoods, bathroom exhaust fans and dryer vents can also contribute to this problem. This is especially true if you have made your house more airtight with new vinyl windows and doors as well as tight weatherstripping.

SOLUTION: Do not have the furnace on at the same time as the fireplace.

New Windows and Doors and Tight Weatherstripping

New windows and doors make for a “tight” house which may create a Fireplace next to windowsmoking problem when the fireplace is in use. A fire requires oxygen and in a tight house, there’s a limited amount of make-up air.

SOLUTION: Cracking open a window or sliding door close to the fireplace will give the fire the oxygen that it needs for the combustion process, and will also help the smoke vent up the chimney.

Canyons and Hillsides

A house located near Wind cap on top of a chimneya canyon or a hillside will be more prone to gusting winds that can create downdrafts. Also, homes located close to the ocean will be prone to the prevailing winds.

SOLUTION: A specially-designed wind cap can sometimes minimize the downdrafts. Note that these wind caps cannot be installed on prefabricated fireplace systems.

Chimney Improperly Built

A masonry chimney is built to a certain formula, having to do with the height and width of the firebox opening, the height of the chimney and the diameter of the flue pipe (among other factors). If any of these factors are not correct, the fireplace may be prone to smoking problems. Also double-sided, L-shape or see-through fireplaces are always more prone to smoking problems.

In addition, if a chimney does not have an adequate height above the roof line, the system may be prone to smoking problems. We call these systems “short stacks.” The chimney should be at least three feet above the roof line, and at3-2-10 Rule least two feet taller than anything horizontally within ten feet. This includes houses located too close together, two-story additions (when the chimney is on the first story), or trees. In building terms, this is called the 3-2-10 rule.

SOLUTION: For a one-sided fireplace opening, sometimes installing a smoke guard will resolve the problem. A smoke guard is a piece of metal that extends the full smoke guard on fireplacewidth at the top of the firebox opening and lowers the firebox opening by 4″, 6″ or 8″, to encourage the smoke from the fireplace to go up the flue instead of in the room.  For multi-sided fireplaces, closing one side of the glass doors may reduce smoking. (Note: Never close both sets of glass doors on a two-sided fireplace at the same time during a fire.)  As a last resort, sometimes the only solution is to have a chimney mason raise the height of the chimney.

Wind

Two systems in one chimney structure can create smoking problems if the two flues are at the same height at the top of the chimney stack, side by side. As one fireplace is used, the smoke goes up and as it exits the top, the wind can drive the smoke down the other flue pipe, like a siphon effect.

SOLUTION: Slightly raise one of the two flues so that they aren’t at the same height at the top of the chimney.

What NOT to do if you have a smoking problem…

Time and time again, homeowners install artificial gas logs to solve a fireplace smoking problem.  This is NOT a viable solution and can actually create a more dangerous situation!

If your fireplace has a smoking problem when you’re burning wood, it’s going to have a smoking problem when you’re burning artificial gas logs, only the gases are colorless and odorless so you won’t be aware there’s a smoking problem.  It’s better to figure out why the fireplace is smoking before installing gas logs.

In Summary…

This is not a complete list of causes for smoking problems but certainly the most common. Using the process of elimination, trying different solutions one at a time, will narrow down the cause so you can enjoy your fireplace to the fullest. Future blog posts will go into further detail on each of these smoking problems.  Keep in mind, the best place to start is to have a CSIA Certified Chimney Sweep out to evaluate your system, sweep if necessary and give you advice on how to resolve any smoking problem that you may be having.